Weed Eater Trimmer 530163751 User Manual

R
Trademark  
Please do not return unit to retailer.  
Por favor, no devuelva el aparato al lugar de compra.  
Veuillez ne pas retourner l’outil au détaillant.  
1-800-554-6723  
Instruction Manual  
Manual de Instrucciones  
Manuel d’Instructions  
GHT 220  
WARNING:  
Read and follow all Safety Rules and Operating Instructions before  
using this product. Failure to do so can result in serious injury.  
ADVERTENCIA:  
Lea el manual de instrucciones y siga todas las advertencias e  
instrucciones de seguridad. El no hacerlo puede resultar en lesiones  
graves.  
AVERTISSEMENT:  
Lire le manuel d’instructions et bien respecter tous les avertisse-  
ments et toutes les instructions de sécurité. Tout défaut de le faire  
pourrait entraîner des blessures graves.  
Electrolux Home Products, Inc.  
250 Bobby Jones Expressway  
Augusta, GA 30907  
Electrolux Canada Corporation  
6150 McLaughlin Road  
Mississauga, ON L5R 4C2  
Copyright E2003 Electrolux Home Products, Inc.  
530163751  
10/9/03  
 
WARNING:  
Blades can throw objects violently.  
D You can be blinded or injured.  
D Wear safety glasses.  
Safety  
Glasses  
Boots  
WARNING:  
Hazard zone for thrown objects  
D Blades can throw objects violently.  
D Others can be blinded or injured.  
D Keep people and animals 30 feet  
(10 meters) away.  
30 ft.  
(10 m)  
Blades move Allow blades to stop  
momentarily before removing  
he them from the cut.  
is  
WARNING:  
Blades move momentarily after the  
trigger is released.  
D The blades can seriously cut you or  
others.  
d.  
D Allow blades to stop before  
removing them from the cut.  
D Do not store the unit or fuel in a closed area  
where fuel vapors can reach sparks or an  
open flame from hot water heaters, electric  
motors or switches, furnaces, etc.  
SPECIAL NOTICE: This unit is equipped  
with a temperature limiting muffler and spark  
arresting screen which meets the require-  
ments of California Codes 4442and 4443. All  
U.S. forest land and the states of California,  
Idaho, Maine, Minnesota, New Jersey, Ore-  
gon, and Washington require by law that  
many internal combustion engines be  
equippedwithaspark arrestingscreen. Ifyou  
operateinalocale wheresuch regulationsex-  
ist, you arelegally responsible formaintaining  
the operatingcondition of theseparts. Failure  
to do so is a violation of the law. Refer to the  
SERVICE section for maintenance of the  
muffler and spark arresting screen.  
D Store the unit so the cutting blade cannot  
accidentally cause injury.  
D Store in a dry area out of reach of children.  
SAFETY NOTICE: Exposure to vibrations  
through prolonged use of gasoline powered  
hand tools could cause blood vessel or nerve  
damage in the fingers, hands, and joints of  
people prone to circulation disorders or ab-  
normal swelling. Prolonged use in cold  
weatherhas beenlinked toblood vessel dam-  
age in otherwise healthy people. If symptoms  
occur such as numbness, pain, loss of  
strength, change in skin color or texture, or  
loss of feeling in the fingers, hands, or joints,  
discontinue the use of this tool and seek  
medical attention. An anti vibration system  
does not guarantee the avoidance of these  
problems. Users who operatepower tools on  
a continual and regular basis must monitor  
closely their physical condition and the condi-  
tion of this tool.  
ASSEMBLY  
NOTE:It is normal for thefuel filter to rattle in  
the empty fuel tank.  
ASSEMBLY  
Your hedgetrimmer is fully assembled; noas-  
sembly is required.  
-- 3 --  
 
OPERATION  
KNOW YOUR HEDGE TRIMMER  
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR  
UNIT. Compare the illustrations with your unit to familiarize yourself with the location of the vari-  
ous controls and adjustments. Save this manual for future reference.  
Muffler  
ON/OFF  
Switch  
Spark Plug  
Throttle Lock  
Hand Guard  
Throttle  
Lock--out  
Throttle  
Trigger  
Primer Bulb  
Fuel Mix Fill Cap  
Choke Lever  
ON/OFF SWITCH  
PRIMER BULB  
The ON/OFF SWITCH is used to stop the en-  
gine. To stop engine, move switch to OFF.  
ThePRIMER BULBremoves air from thecar-  
buretor and fuel lines and fills them with fuel.  
This allows you to start the engine with fewer  
pulls on the starter rope. Activate the primer  
bulb by pressing it and allowing it to return to  
its original position.  
CHOKE  
The CHOKE helps to supply fuel to the engine  
to aid in cold starting. Activate the choke by  
moving choke lever to the desired position. See  
STARTING YOUR ENGINE for complete start-  
ing information.  
THROTTLE TRIGGER  
The THROTTLE TRIGGER controls engine  
speed. Squeeze the trigger for full speed opera-  
tion; release it for idle speed.  
IMPORTANT  
WARNING: Muffler is very hot during  
and after use. Do not touch the muffler or al-  
low combustible material such as dry grass or  
fuel to do so.  
Experience indicates that alcohol blended fuels  
(called gasohol or using ethanol or methanol)  
can attract moisture which leads to separation  
and formation of acids during storage. Acidic  
gas can damage the fuel system of an engine  
while in storage. To avoid engine problems,  
empty the fuel system before storage for 30  
days or longer. Drain the gas tank, start the en-  
gine and let it run until the fuel lines and carbure-  
tor are empty. Use fresh fuel next season. Nev-  
er use engine or carburetor cleaner products in  
the fuel tank or permanent damage may occur.  
BEFORE STARTING ENGINE  
WARNING: Be sure to read the fuel  
information in the safety rules before you be-  
gin. If you do not understandthe safety rules,  
do not attempt to fuel your unit. Call  
1-800-554-6723.  
OPERATING INSTRUCTIONS  
IMPORTANT POINTS  
S Use the minimum throttle speed necessary  
to effectively cut hedges for optimal hedge  
trimmer performance.  
S Never attempt to use this hedge trimmer to  
cut hedges that have any branches with a  
diameter larger than 7/16" (1 cm).  
FUELING ENGINE  
WARNING: Remove fuel cap slowly  
when refueling.  
This engine is certified to operate on un-  
leaded gasoline. Before operation, gasoline  
must be mixed with a good quality synthetic  
2-cycle air-cooled engine oil designed to be  
mixed at a ratio of 40:1. Poulan/Weed Eater  
brand synthetic oil is recommended. A 40:1  
ratio is obtained by mixing 3.2 ounces (95 ml)  
of oil with 1 gallon (4 liters) of unleaded gaso-  
line. DO NOT USE automotive oil or boat oil.  
These oils will cause engine damage. When  
mixing fuel, follow instructions printed on oil  
container. Once oil is added to gasoline,  
shake container momentarily to assure that  
thefuel is thoroughly mixed. Always readand  
follow the safety rules listed under HANDLE  
FUEL WITH CAUTION.  
OPERATING POSITION  
Hearing  
Protection  
tion  
-- 4 --  
 
Primer Bulb  
STOPPING YOUR ENGINE  
D To stop the engine, move the ON/OFF  
switch to the OFF position.  
Choke  
Lever  
STARTING YOUR ENGINE  
D
D
Fuel engine. Move at least 10 feet (3 me-  
ters) away from the fueling site.  
Hold the unit on the ground in the starting  
position as shown. Support unit so the  
blade is off of the ground and away from  
trees, bushes, onlookers, etc.  
5. Pull starter rope handle sharply until en-  
gine sounds as if it is trying to run, but do  
not pull rope more than 6 times.  
6. Move the choke lever to the HALF  
CHOKE position.  
7. Pull starter rope sharply until the engine  
runs, but no more than 6 pulls.  
STARTING A COLD ENGINE (or a  
warm engine after running out of  
fuel)  
NOTE: If the engine doesn’t start after 6  
pulls (at the HALF CHOKE position),  
check to make sure the ON/OFF switch is  
in the ON position. Move the choke lever  
to the FULL CHOKE position and press  
the primer bulb 6 times; pull the starter  
rope 2 more times. Move the choke lever  
to the HALF CHOKE position and pull the  
starter rope until the engine runs, but no  
more than 6 more pulls. If the engine still  
doesn’t start, it is probably flooded. Pro-  
ceed to STARTING A FLOODED EN-  
GINE.  
8. Once the engine starts, allow the engine to  
run 10 seconds, then move the choke lever  
totheOFF CHOKE position. Allow the unit to  
run for 30 more seconds at the OFF CHOKE  
position before squeezing and releasing the  
throttle trigger to release the throttle lock.  
NOTE:If enginedies withthe chokelever  
in the OFF CHOKE position, move the  
choke lever to the HALF CHOKE position  
and pull the rope until the engine runs, but  
no more than 6 pulls.  
Throttle Lock  
Throttle  
Lock-out  
Throttle  
Trigger  
1. Move the ON/OFF switch to the ON posi-  
tion.  
2. Engage the throttle lock as follows:  
D press the throttle lock--out;  
D squeeze and hold throttle trigger;  
D press and hold throttle lock, then  
D release the throttle trigger  
NOTE: Keep the throttle lock engaged until  
the engine starts.  
STARTING A WARM ENGINE  
1. Move the ON/OFF switch to the ON posi-  
tion.  
2. Slowly press the primer bulb 6 times.  
3. Move the choke lever to the HALF  
CHOKE position.  
4. Engage the throttle lock as directed in  
STARTING A COLD ENGINE.  
NOTE: Keep the throttle lock engaged until  
the engine starts.  
ON  
OFF  
Switch  
5. Pull starter rope sharply until engine runs,  
but no more than 5 pulls.  
6. Allow the engine to run 10 seconds, then  
move the choke lever to the OFF CHOKE  
position.  
7. Releasethethrottlelock by squeezingand  
releasing the trigger.  
NOTE: If engine has not started, pull starter  
rope5morepulls. If enginestill doesnot run,it  
is probably flooded. Proceedto STARTING A  
FLOODED ENGINE.  
3. Slowly press the primer bulb 6 times.  
4. Move the chokelever tothe FULLCHOKE  
position.  
-- 5 --  
 
STARTING A FLOODED ENGINE  
Flooded engines can be started by placing  
theON/OFF switch in the ONposition andthe  
choke lever in the OFF CHOKE position and  
engaging the throttle lock as directed in the  
STARTING A COLD ENGINE section; then,  
pull the rope to clear the engine of excess  
fuel. Starting could require pulling the starter  
rope many times depending on how badly the  
unit is flooded. If the unit still doesn’t start, refer  
to the TROUBLESHOOTING TABLE or call  
1-800-554-6723.  
Cleaning the air filter:  
A dirty air filter decreases engine perform-  
ance and increases fuel consumption and  
harmful emissions. Always clean after every  
5 hours of operation.  
1. Clean the cover and the area around it to  
keep debris from falling into thecarburetor  
chamber when the cover is removed.  
2. Remove parts as illustrated.  
NOTE: Do not clean filter in gasoline or other  
flammable solvent. Doing so can create a fire  
hazard or produce harmful evaporative emis-  
sions.  
3. Wash the filter in soap and water.  
4. Allow filter to dry.  
5. Add a few drops of oil to the filter; squeeze  
filter to distribute oil.  
6. Replace parts.  
SERVICE  
WARNING: Ensure ON/OFF switch  
is in the OFF position and disconnect the  
spark plug before performing maintenance  
except for carburetor adjustments.  
GENERAL RECOMMENDATIONS  
Thewarrantyonthis unit doesnot cover items  
that have been subjected to operator abuse  
or negligence. To receive full value from the  
warranty, the operator must maintain unit as  
instructed in this manual. Various adjust-  
ments will need to be made periodically to  
properly maintain your unit.  
CHECK FOR LOOSE  
FASTENERS AND PARTS  
S Spark Plug Boot  
S Air Filter  
S Housing Screws  
INSPECT MUFFLER AND SPARK  
ARRESTING SCREEN  
NOTE: THE SPARK ARRESTING SCREEN  
ON THIS UNIT IS NOT SERVICEABLE.  
For normal homeowner use, the muffler and  
spark arresting screen will not require any ser-  
vice.  
After 50 hours of use, we recommend that  
your muffler be replaced by an authorized  
service dealer.  
CARBURETOR ADJUSTMENT  
WARNING: Keep others away when  
making idle speed adjustments. The blade  
will be moving during most of this procedure.  
Wear your protective equipment andobserve  
all safety precautions. When making adjust-  
ments, use a screwdriver short enough to  
keep your hands behind the handguard and  
away from the blade. After making adjust-  
ments, the blade mustnot moveat idle speed.  
The carburetor has been carefully set at the  
factory. Adjustments may benecessary if you  
notice any of the following conditions:  
S Engine will not idle when the throttle is re-  
leased.  
CHECK FOR DAMAGED OR  
WORN PARTS  
Contact an authorized service dealer for re-  
placement of damaged or worn parts.  
S ON/OFF Switch -- Ensure ON/OFF switch  
functions properly by moving the switch to the  
OFF position. Make sure engine stops; then  
restart engine and continue.  
S Fuel Tank -- Do not use unit if fuel tank shows  
signs of damage or leaks.  
S The blade moves at idle.  
INSPECT AND CLEAN UNIT AND  
LABELS  
S Before and after each use, inspect com-  
plete unit for loose or damaged parts. After  
each use, clean the unit and labels using a  
damp cloth with a mild detergent.  
S Wipe off unit with a clean dry cloth.  
Keep others away when making idle speed  
adjustments. Make adjustments with the unit  
resting on a level surface free of debris that  
can be caught in the hedge trimmer blade.  
Serious injury to the operator and others can  
occur if the carburetor is not properly ad-  
justed. Keep all parts of your body away from  
the blade and muffler.  
CLEAN AIR FILTER  
Idle Speed Adjustment  
Air Filter  
Cover  
Allow engineto idle. Adjust speed until engine  
runswithoutblademoving(idle toofast) oren-  
gine stalling (idle speed too slow).  
S Turn idle speed screw clockwise to in-  
creaseenginespeedif enginestalls ordies.  
S Turn idle speed screw counterclockwise to  
decrease engine speed if the blade moves  
at idle.  
WARNING: Recheck the idle speed  
after each adjustment. The blade must not  
move at idle speed to avoid serious injury to  
the operator or others.  
Air Filter  
Screw  
-- 6 --  
 
Idle Speed Screw  
SEASONAL STORAGE  
Prepareunit for storage at end of season or if  
it will not be used for 30 days or more.  
If your unit is to be stored for a period of time:  
S Clean the entire unit.  
S Store in a clean dry area.  
S Clean all parts and check for damage.  
Have damaged parts repaired or replaced  
by an authorized service dealer.  
S Keep all nuts, bolts, and screws tight.  
S Lightly oil external metal surfaces, includ-  
ing the blade.  
To oil the blade, do the following:  
S Stop the engine and allow blade to come to  
a complete stop.  
S Ensure ON/OFF switch is in the OFF posi-  
tion.  
S Disconnect the spark plug wire.  
S Apply a light machine oil along the edge of  
the top strap as shown.  
If you requirefurtherassistance or areunsure  
about performing this procedure, contact an  
authorized  
service  
dealer  
or  
call  
1--800--554--6723.  
REPLACE SPARK PLUG  
Replace spark plug each year to ensure the  
engine starts easier and runs better. Set  
spark plug gap at 0.025 inch. Ignition timing is  
fixed, nonadjustable.  
OIL  
1. Twist, then pull off spark plug boot.  
2. Remove spark plug from cylinder and dis-  
card.  
Top Strap  
3. Replace with Champion RCJ-6Y spark  
plug and tighten securely with a 3/4 inch  
socket wrench.  
4. Reinstall the spark plug boot.  
FUEL SYSTEM  
Under FUELING ENGINE in the OPERA-  
TION section of this manual,see messagela-  
beled IMPORTANT regarding the use of ga-  
sohol in your engine. Fuel stabilizer is an ac-  
ceptable alternative in minimizing the formation  
of fuel gum deposits during storage. Add stabi-  
lizer to gasoline in fuel tank or fuel storage con-  
tainer. Follow the mix instructions found on sta-  
bilizer container. Run engine at least 5 minutes  
after adding stabilizer.  
REPLACE FUEL FILTER  
Toreplacefuel filter, drainunit by runningit dry  
of fuel, then remove fuel cap/retainer assem-  
bly from tank. Pull filter from tank andremove  
it fromthe fuel line. Install new fuelfilter onfuel  
line; reinstall parts.  
ENGINE  
Fuel Filter  
S Remove spark plug and pour 1 teaspoonof  
40:1, 2-cycle engine oil (air cooled) through  
the spark plug opening. Slowly pull the  
starter rope 8 to 10 times to distribute oil.  
S Replace spark plug with new one of recom-  
mended type and heat range (see RE-  
PLACE SPARK PLUG section).  
S Clean air filter.  
Fuel Line  
S Check entire unit for loose screws, nuts,  
and bolts. Replace any damaged, broken,  
or worn parts.  
S At the beginning of the next season, use  
only fresh fuel having thepropergasolineto  
oil ratio.  
STORAGE  
WARNING: Perform the following  
steps after each use:  
S Allow engine to cool, and secure the unit  
before storing or transporting.  
OTHER  
S Do not store gasoline from one season to  
another.  
S Replace your gasoline can if it starts torust.  
S Store unit and fuel in a well ventilated area  
where fuel vapors cannot reach sparks or  
open flames from water heaters, electric  
motors or switches, furnaces, etc.  
S Store unit with all guards in place. Position  
unit so that any sharp object cannot acci-  
dentally cause injury.  
NEED ASSISTANCE?  
NEED ASSISTANCE?  
Call 1-800-554-6723 for assistance.  
NEED SERVICE PARTS?  
Contact your authorized service dealer.  
S Store unit and fuel well out of the reach of  
children.  
-- 7 --  
 
TROUBLESHOOTING TABLE  
WARNING: Always stop unitand disconnectspark plugbeforeperformingall ofthe  
recommended remedies below except remedies that require operation of the unit.  
TROUBLE  
CAUSE  
REMEDY  
Engine will not  
start.  
1. ON/OFF switch in the  
OFF position.  
2. Engine flooded.  
1. Move ON/OFF switch to the ON  
position.  
2. See “Starting a Flooded Engine”  
in Operation Section.  
3. Fuel tank empty.  
4. Spark plug not firing.  
5. Fuel not reaching  
carburetor.  
3. Fill tank with correct fuel mixture.  
4. Install new spark plug.  
5. Check for dirty fuel filter; replace.  
Check for kinked or split fuel line;  
repair or replace.  
6. Compression low.  
6. Contact an authorized service dealer.  
Engine will  
not idle  
properly.  
1. Carburetor requires  
adjustment.  
2. Crankshaft seals worn.  
3. Compression low.  
1. See “Carburetor Adjustment” in  
Service and Adjustments Section.  
2. Contact an authorized service dealer.  
3. Contact an authorized service dealer.  
Engine will not  
accelerate,  
lacks power,  
or dies under  
a load.  
1. Air filter dirty.  
1. Clean or replace air filter.  
2. Clean or replace plug  
and regap.  
2. Spark plug fouled.  
3. Carburetor requires  
adjustment.  
4. Carbon build-up on  
muffler outlet screen.  
5. Compression low.  
3. Contact an authorized service dealer.  
4. Contact an authorized service dealer.  
5. Contact an authorized service dealer.  
Engine  
1. Choke partially on.  
1. Adjust choke.  
2. Fuel mixture incorrect.  
2. Empty fuel tank and refill with  
correct fuel mixture.  
smokes  
excessively.  
3. Air filter dirty.  
4. Carburetor requires  
adjustment.  
3. Clean or replace air filter.  
4. Contact an authorized service dealer.  
Engine runs  
hot.  
1. See “Fueling Engine” in Operation  
section.  
2. Replace with correct spark plug.  
3. Contact an authorized service dealer.  
1. Fuel mixture incorrect.  
2. Spark plug incorrect.  
3. Carburetor requires  
adjustment.  
4. Carbon build-up on  
muffler outlet screen.  
4. Contact an authorized service dealer.  
-- 8 --  
 
LIMITED WARRANTY  
ELECTROLUX HOME PRODUCTS, INC.,  
cover predelivery setup or normal adjustments  
warrants to the original purchaser that each new  
Weed EaterR brand gasoline tool or attach-  
ment is free from defects in material and work-  
manship and agrees to repair or replace under  
this warranty any defective gasoline product or  
attachment as follows from the original date of  
purchase.  
explained in the instruction manual.  
THIS WARRANTY GIVES YOU SPECIFIC  
LEGAL RIGHTS, AND YOU MAY HAVE  
OTHER RIGHTS WHICH VARY FROM  
STATE TO STATE.  
NO CLAIMS FOR CONSEQUENTIAL OR  
OTHER DAMAGES WILL BE ALLOWED,  
AND THERE ARE NO OTHER EXPRESS  
WARRANTIES EXCEPT THOSE EX-  
PRESSLY STIPULATED HEREIN.  
SOME STATES DO NOT ALLOW LIMITA-  
TIONS ON HOW LONG AN IMPLIED WAR-  
RANTY LASTS OR THE EXCLUSION OR  
LIMITATIONS OF INCIDENTAL OR CONSE-  
QUENTIAL DAMAGES, SO THE ABOVE LIM-  
ITATIONS OR EXCLUSION MAY NOT APPLY  
TO YOU.  
2 YEARS -- Parts and Labor, when used for  
household purposes.  
60 DAYS -- Parts and Labor, when used for  
commercial, professional, or income producing  
purposes.  
30 DAYS -- Parts and Labor, if used for rental  
purposes.  
This warranty is not transferable and does not  
cover damage or liability caused by improper  
handling, improper maintenance, or the use of  
accessories and/or attachments not specifically  
recommended by ELECTROLUX HOME  
PRODUCTS, INC., for this tool. Additionally,  
this warranty does not cover tune--ups, spark  
plugs, filters, starter ropes, starter springs, cut-  
ting line, or rotating head parts that will wear and  
require replacement with reasonable use during  
the warranty period. This warranty does not  
The policy of ELECTROLUX HOME PROD-  
UCTS, INC., is to continuously improve its prod-  
ucts.  
Therefore, ELECTROLUX HOME  
PRODUCTS, INC., reserves the right to  
change, modify, or discontinue models, de-  
signs, specifications, and accessories of all  
products at any time without notice or obligation  
to any purchaser.  
U.S. EPA / ENVIRONMENT CANADA  
EMISSION CONTROL WARRANTY STATEMENT  
YOUR WARRANTY RIGHTS AND OB-  
LIGATIONS: The U. S. Environmental  
ProtectionAgency, EnvironmentCanadaand  
ELECTROLUX HOME PRODUCTS, INC.,  
are pleased to explain the emissions control  
system warranty on your year 2002--2004  
deny warrantysolely forthe lack of receipts or  
for your failure to ensure the performance of  
all scheduled maintenance. As thesmall off--  
road engine owner, you should be aware that  
ELECTROLUX HOME PRODUCTS, INC.,  
may deny you warranty coverage if your  
small off--road engine or a part of it has failed  
due to abuse, neglect, improper mainte-  
nance, unapproved modifications, or the use  
of parts not made or approved by the original  
equipment manufacturer. You are responsi-  
ble for presenting your small off--road engine  
to an ELECTROLUX HOME PRODUCTS,  
INC., authorized repair center as soon as a  
problem exists. Warranty repairs should be  
completed in a reasonable amount of time,  
not to exceed 30 days. If you have any ques-  
tions regarding your warranty rights and re-  
sponsibilities, you should contact your near-  
est authorized service center or call ELEC-  
TROLUX HOME PRODUCTS, INC., at  
small off--road engine.  
ELECTROLUX  
HOME PRODUCTS, INC., must warrant the  
emission control system on your small off--  
road engine for the periods of time listed be-  
low provided there has been no abuse, ne-  
glect, or improper maintenance of your small  
off--road engine. Your emission control sys-  
temincludes partssuch as the carburetorand  
the ignition system. Where a warrantable  
condition exists, ELECTROLUX HOME  
PRODUCTS, INC., will repair your small off--  
road engine at no cost to you. Expenses cov-  
ered under warranty include diagnosis, parts  
and labor. MANUFACTURER’S WARRAN-  
TY COVERAGE: If any emissions related  
part on your engine (as listed under Emis-  
sions Control Warranty Parts List) is defec-  
tive or a defect in the materials or workman-  
ship of the engine causes the failure of such  
an emission related part, the part will be re-  
paired or replaced by ELECTROLUX HOME  
PRODUCTS, INC. OWNER’S WARRANTY  
RESPONSIBILITIES: As the small off--road  
engineowner, youareresponsiblefor theper-  
formance of the required maintenance listed  
in your instruction manual. ELECTROLUX  
HOME PRODUCTS,INC., recommends that  
you retain all receipts covering maintenance  
on your small off--road engine, but ELEC-  
TROLUX HOME PRODUCTS, INC., cannot  
1--800--554--6723.  
WARRANTY COM-  
MENCEMENT DATE: The warranty period  
begins on the date the small off--road engine  
is purchased. LENGTH OF COVERAGE:  
This warranty shall be for a period of two  
years fromthe initial dateofpurchase. WHAT  
IS COVERED: REPAIR OR REPLACE-  
MENT OF PARTS. Repair or replacement of  
any warranted part will be performed at no  
charge to the owner at an approved ELEC-  
TROLUX HOME PRODUCTS, INC., servic-  
ing center. If you have any questions regard-  
ing your warranty rights and responsibilities,  
you should contact your nearest authorized  
service center or call ELECTROLUX HOME  
-- 9 --  
 
PRODUCTS, INC., at 1--800--554--6723.  
WARRANTY PERIOD: Any warranted part  
which is not scheduled for replacement as re-  
quired maintenance, or which is scheduled  
only for regular inspection to the effect of “re-  
pair or replace as necessary” shall be war-  
ranted for 2 years. Any warranted part which  
is scheduled for replacement as required  
maintenanceshall bewarrantedfor theperiod  
of time up to the first scheduled replacement  
point for that part. DIAGNOSIS: The owner  
shall not be charged for diagnostic labor  
which leads to the determination that a war-  
ranted part is defective if the diagnostic work  
is performed at an approved ELECTROLUX  
HOME PRODUCTS, INC., servicing center.  
CONSEQUENTIAL DAMAGES: ELEC-  
TROLUX HOME PRODUCTS, INC., may be  
liable for damages to other engine compo-  
nents caused by the failure of a warranted  
part still under warranty. WHAT IS NOT  
COVERED: All failures caused by abuse, ne-  
glect, or improper maintenance are not cov-  
ered. ADD-ON OR MODIFIED PARTS: The  
use of add--on or modified parts can be  
grounds for disallowing a warranty claim.  
ELECTROLUXHOME PRODUCTS, INC., is  
not liable to cover failures of warranted parts  
caused by the use of add--on or modified  
parts. HOW TO FILE A CLAIM: If you have  
any questions regarding your warranty rights  
and responsibilities, you should contact your  
nearest authorized service center or call  
ELECTROLUXHOMEPRODUCTS, INC.,at  
1--800--554--6723. WHERE TO GET WAR-  
RANTY SERVICE: Warranty services or re-  
pairs shall be provided at all ELECTROLUX  
HOME PRODUCTS, INC., service centers.  
Call 1--800--554--6723. MAINTENANCE,  
REPLACEMENT AND REPAIR OF EMIS-  
SION RELATED PARTS: Any ELECTRO-  
LUX HOME PRODUCTS, INC., approvedre-  
placement part used in the performance of  
any warranty maintenance or repair on emis-  
sion related parts will be provided without  
charge to the owner if the part is under war-  
ranty. EMISSION CONTROL WARRANTY  
PARTS LIST: Carburetor, Ignition System:  
Spark Plug (covered up to maintenance  
schedule), Ignition Module. MAINTENANCE  
STATEMENT: The owner is responsible for  
the performance of all required maintenance  
as defined in the instruction manual.  
The information on the product label indicates which standard your engine is certified.  
Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.  
This engine is certified to be emissions compliant for the following use:  
Moderate (50 hours)  
Intermediate (125 hours)  
Extended (300 hours)  
-- 1 0 --  
 

Weider Home Gym WESY81080 User Manual
Weider Home Gym WESY81081 User Manual
Weslo Elliptical Trainer WLTL499070 User Manual
Whirlpool Freezer EV201NZRQ00 User Manual
Winegard TV Antenna FV HDC3 User Manual
Xerox All in One Printer 130 B 141 User Manual
X Micro Tech Computer Drive 11G User Manual
Yamaha Music Mixer Expansion Kit User Manual
Yamaha Portable Speaker IF2112M 64W User Manual
Zenith Flat Panel Television L15V36 User Manual