R
Trademark
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
B1750
IMPORTANT MANUAL - Do not throw away
MANUAL IMPORTANTE - No lo descarte
MANUEL IMPORTANT - À Conserver
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Veuillez lire le manuel d’instructions et bien respecter tous les
avertissements et toutes les instructions de sécurité. Tout défaut
de le faire pourrait entraîner des blessures graves.
Electrolux Home Products, Inc.
104 Warren Road
Augusta, GA 30907
Copyright E2004 Electrolux Home Products, Inc.
530165303-01
6/10/04
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek
medical attention. An antivibration system
does not guarantee the avoidance of these
problems. Users who operate power tools on
a continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
MAINTAIN YOUR UNIT PROPERLY
D Have all maintenance other than the rec-
ommended procedures described in the in-
struction manual performed by an autho-
rized service dealer.
D Disconnect spark plug before performing
maintenance except for carburetor adjust-
ments.
D Use only recommended Weed EaterŽ re-
placement parts; use of any other parts
may void your warranty and cause damage
to your unit.
D Empty fuel tank before storing the unit. Use
up fuel left in carburetor by starting engine and
letting it run until it stops.
D Do not use any accessory or attachment
other than those recommended by manufac-
turer for use with your unit.
D Do not store the unit or fuel in a closed area
where fuel vapors can reach sparks or an
open flame from hot water heaters, electric
motors or switches, furnaces, etc.
D Store in a dry area out of reach of children.
SPECIAL NOTICE: Exposure to vibra-
tions through prolonged use of gasoline pow-
ered hand tools could cause blood vessel or
nerve damage in the fingers, hands, and
joints of people prone to circulation disorders
or abnormal swelling. Prolonged use in cold
weather has beenlinked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
SPECIAL NOTICE: For users on U.S. For-
est Land and in some states, including Cali-
fornia (Public Resources Codes 4442 and
4443), Idaho, Maine, Minnesota, New Jersey,
Oregon, and Washington: Certain internal
combustion engines operated on forest,
brush, and/or grass covered landin the above
areas are required to be equipped with a
spark arresting screen, maintained in effec-
tive working order, or the engine must be con-
structed, equipped, and maintained for the
prevention of fire. Check with your state or lo-
cal authorities for regulations pertaining to
these requirements. Failure to follow these
requirements is a violation of thelaw. This unit
is not factory equipped with a spark arresting
screen; however, a spark arresting screen is
available as an optional part. If a spark arrest-
ing screen is required in your area, contact
your authorized service dealer for the correct
kit. The spark arresting screen, blower tubes,
and nozzles must be assembled to unit to be
in full compliance with regulations.
ASSEMBLY
NOTE: Knob must be loose enough to allow
blower tube to be inserted in blower outlet.
Loosen knob by turning counterclockwise.
WARNING: This unit is intended for
blower use only. Do not attempt to open inlet
cover. Openedor damaged inlet cover can re-
sult in serious injury. Discontinue use of blow-
er immediately if inlet cover becomes opened
or damaged. Take unit to your nearest autho-
rized service dealer for repair.
Blower
Blower
Outlet
Tube
WARNING: If you receive your unit
assembled, check each step to insure your
unit is properly assembled and all fasteners
are secure. Follow all safety information in
the manual and on the unit.
BLOWER TUBE ASSEMBLY
1. Align the rib on the blower tube with the
groove in the blower outlet; slide the tube
into place.
Groove
Rib
2. Secure the tube by turning the knob clock-
wise.
3. To remove the tube, turn the knobcounter-
clockwise to loosen the tube; remove the
tube.
-- 3 --
OPERATION
KNOW YOUR BLOWER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.
Compare the illustrations with your unit to familiarize yourself with the location of the various controls
and adjustments. Save this manual for future reference.
Primer Button
Choke Lever
Fuel Mix
Throttle
Fill Cap
Lever
Starter
Rope
Spark Plug
Blower
Tube
Rear
Handle
THROTTLE LEVER
CHOKE LEVER
The THROTTLE LEVER is used to select the
desired engine speed and to stop the engine.
The CHOKE helps to supply fuel to the engine
to aid in cold starting. Activate the choke by
moving the choke lever to the FULL CHOKE
position. After engine attempts to start, move the
choke lever to the HALF CHOKE position.
Once engine starts, move choke lever to the
RUN position.
Movethethrottlelever to the
full speed operation. Move the throttle lever
position for
to the
positionfor idlespeed. To stop the
engine, move the throttle lever to the STOP
position.
PRIMER BUTTON
The PRIMER BUTTON removes air from the
carburetor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate primer button
by pressing it and allowing it to return to its origi-
nal position.
S Operate power equipment only at reasonable
hours--not early in the morning or late at night
when people might be disturbed. Comply with
times listed in local ordinances. Usual recom-
mendations are 9:00 a.m. to 5:00 p.m.,
Monday though Saturday.
OPERATING POSITION
Eye
Protection
S To reduce noise levels, limit the number of
pieces of equipment used at any one time.
S To reduce noise levels, operate power
blowers at the lowest possible throttle
speed to do the job.
S Use rakes and brooms to loosen debris be-
fore blowing.
S In dusty conditions, slightly dampen sur-
faces or use a mister attachment when wa-
ter is available.
Blower
OPERATING TIPS
S While blowing debris, hold the unit with the
muffler side facing away from your body
and clothes (see OPERATING POSITION
illustration above).
S To reduce the risk of hearing loss
associated with sound level(s), hearing
protection is required.
S To reduce the risk of injury associated with
contacting rotating parts, stop the engine be-
fore installing or removing attachments. Do
not operate without guard(s) in place.
S Conserve water by using power blowers
instead of hoses for many lawn and garden
applications, including areas such as gutters,
screens, patios, grills, porches, and gardens.
S Watch out for children, pets, open windows,
or freshly washed cars. Blow debris away
safely.
S Use the full blower nozzle extension so the
air stream can work close to the ground.
-- 4 --
S After using blowers and other equipment,
CLEAN UP! Dispose of debris in trash re-
ceptacles.
TO STOP THE ENGINE
D To stop the engine, move the throttle lever
to the STOP position.
BEFORE STARTING ENGINE
BEFORE STARTING THE ENGINE
WARNING: Be sure to read the fuel
information in the safety rules before you be-
gin. If you do not understand the safety rules,
do not attempt to fuel your unit. Call
1-800-554-6723.
WARNING: You MUST make sure
the tubes are secure before using the unit.
D
Fuel engine. Move at least 10 feet (3 me-
ters) away from the fueling site.
Hold the unit in the starting position as
shown. Make sure the blower end is di-
rected away from people, animals, glass,
and solid objects.
D
FUELING ENGINE
WARNING: Remove fuel cap slowly
when refueling.
This engine is certified to operate on unleaded
gasoline. Before operation, gasoline must be
mixed with a good quality synthetic 2-cycle
air-cooled engine oil designed to be mixed at a
ratio of 40:1. Poulan/Weed Eater brand
synthetic oil is recommended. Mix gasoline and
oil at a ratio of 40:1. A 40:1 ratio is obtained by
mixing 3.2 ounces (95 ml) of oil with 1 gallon (4
liters) of unleaded gasoline. DO NOT USE
automotive oil or boat oil. These oils will cause
engine damage. When mixing fuel, follow
instructions printed on container. Once oil is
added to gasoline, shake container momentarily
to assure that the fuel is thoroughly mixed.
Always read and follow the safety rules relating
to fuel before fueling your unit.
STARTING POSITION
WARNING: When starting engine,
hold the unit as illustrated. Do not set unit on any
surface except a clean, hard area when starting
engine or while engine is running. Debris such
as gravel, sand, dust, grass, etc. could be
picked up by the air intake and thrown out
through the discharge opening, damaging the
unit or property, or causing serious injury to by-
standers or the operator.
IMPORTANT
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads to
separation and formation of acids during
storage. Acidic gas can damage the fuel
system of an engine while in storage. Toavoid
engine problems, empty the fuel system
before storage for 30 days or longer. Drain the
gas tank, start theengine and let it run until the
fuel lines and carburetor are empty. Use fresh
fuel next season. Never use engine or
carburetor cleaner products in the fuel tank or
permanent damage may occur.
STARTING A COLD ENGINE
1. Move throttle lever to the
position.
2. Move choke lever to the FULL CHOKE
position.
3. Slowly press the primer button 8 times.
T
NOTE: Unit must be placed on its side when
adding fuel (see illustration below).
Choke Lever
4. Pull starter rope sharply until engine at-
tempts to run, but nomore than 5 pulls (be-
low 30_ F, 8 pulls).
NOTE: If engine attempts to start before the
th
5
pull, go to next step immediately.
5. Move the choke lever to the HALF
CHOKE position.
6. Pull the starter rope sharply until the en-
gine runs, but no more than 5 pulls (below
30_ F, 10 pulls).
7. After a 5 second warm--up, move the
choke lever to the RUN position.
8. Allow the unit to run for 30 more seconds
at the RUN position before moving the
throttle lever to
position.
-- 5 --
If engine has not started after 5 pulls (at HALF
CHOKE), repeat STARTING A COLD ENGINE
procedure. If engine still does not start, proceed
to STARTING A FLOODED ENGINE.
9. To stop the engine, move the throttle lever to
the STOP position.
STARTING A WARM ENGINE
NOTE: If fuel tank is empty, add fuel; then,
follow STARTING A COLD ENGINE proce-
dure. Do not fill fuel tank while engine is hot.
3. To stop the engine, move the throttle lever to
the STOP position.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing the
choke lever in the RUN position. Move throttle
lever to the fast position
; then, pull rope
until engine starts. After engine starts, move the
throttle lever to the slow position
engine to idle.
to allow
Starting could require pulling the starter rope
many times depending on how badly the unit is
flooded.
1. Move throttle lever to the
position.
2. Pull starter rope sharply until engine runs,
but no more than 5 pulls.
If unit still doesn’t start refer to the TROUBLE-
SHOOTING TABLE or call 1-800-554-6723.
NOTE: If engine has not started, pull starter
rope 5 more pulls. If engine still does not run,
it is probably flooded.
MAINTENANCE
CLEAN AIR FILTER
WARNING: Avoid touching muffler
unless engine and muffler are cold. A hot
muffler can cause serious burns.
Air Filter
Cover
WARNING: This unit is intended for
blower use only. Do not attempt to open inlet
cover. Openedor damaged inlet cover can re-
sult in serious injury. Discontinue use of blow-
er immediately if inlet cover becomes opened
or damaged. Take unit to your nearest autho-
rized service dealer for repair.
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover items
that have been subjected to operator abuse
or negligence. To receive full value from the
warranty, the operator must maintain unit as
instructed in this manual. Various adjust-
ments will need to be made periodically to
properly maintain your unit.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Spark Plug Boot
S Air Filter
S Housing Screws
S Muffler
Screws
Air Filter
Cleaning the air filter:
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean or replace
air filter after every 5 hours of operation or
yearly, whichever comes first.
1. Clean the cover and the area around it to
keep debris from falling into the carburetor
chamber when the cover is removed.
2. Remove parts as illustrated.
NOTE: Do not clean filter in gasoline or other
flammable solvent. Doing so can create a fire
hazard or produce harmful evaporative emis-
sions.
CHECK FOR DAMAGED OR WORN
PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S Throttle Lever -- Ensure throttle lever func-
tions properly by moving the throttle lever to
the STOP position. Make sure engine
stops; then restart engine and continue.
S Fuel Tank -- Do not use unit if fuel tank shows
signs of damage or leaks.
3. Wash the filter in soap and water.
4. Allow filter to dry.
5. Apply a few drops of oil to the filter;
squeeze filter to distribute oil.
6. Replace parts.
REPLACE SPARK PLUG
INSPECT AND CLEAN UNIT AND
DECALS
Replace spark plug each year to ensure the
engine starts easier and runs better. Set
spark plug gap at 0.025 inch. Ignition timing is
fixed, nonadjustable.
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit and
decals using a damp cloth with a milddeter-
gent.
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder and dis-
card.
S Wipe off unit with a clean dry cloth.
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
socket wrench.
4. Reinstall the spark plug boot.
-- 6 --
Mounting
Screw
Holes
REPLACE FUEL FILTER
Toreplace fuel filter, drain unit by running it dry
of fuel, then remove fuel cap/retainer assem-
bly from tank. Pull filter from tank and remove
it fromthe fuel line. Install new fuelfilter on fuel
line; reinstall parts.
Muffler Cover
Screws
Fuel Line
Fuel Filter
1. Loosen and remove the 2 screws from the
muffler cover.
2. Remove the muffler cover.
3. Tighten the 2 muffler mounting screws se-
curely.
4. Reinstall muffler cover and 2 screws.
Tighten securely.
CARBURETOR ADJUSTMENT
There is no screw for idle adjustment on your
blower. The throttle lever is used to control
engine speed. The throttle lever can be
placed in one of four positions: STOP, IDLE
CHECK MUFFLER MOUNTING
SCREWS
Once each year, ensure muffler mounting
screws are secure and tightened properly to
prevent damage.
or
, FULL THROTTLE or
, and one
intermittent position. If your enginewill not run
properly or you require further assistance,
contact an authorized service dealer or call
1--800--554--6723.
STORAGE
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to gasoline in fuel
tank or fuel storage container. Follow the mix
instructions found on stabilizer container. Run
engine at least 5 minutes after adding stabilizer.
WARNING: Perform the following
steps after each use:
S Allow engine to cool, and secure the unit
before storing or transporting.
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
ENGINE
S Remove spark plug and pour 1 teaspoon of
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
S Replace spark plug with new one of recom-
mended type and heat range.
S Store unit and fuel well out of the reach of
children.
S Clean air filter.
SEASONAL STORAGE
S Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
S Clean the entire unit before lengthy stor-
age.
S At the beginning of the next season, use
only fresh fuel having the proper gasolineto
oil ratio.
S Store in a clean dry area.
S Lightly oil external metal surfaces.
OTHER
S Do not store gasoline from one season to
another.
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TION section of this manual, see messagela-
beled IMPORTANT regarding the use of ga-
sohol in your engine.
S Replace your gasoline can if it starts to rust.
-- 7 --
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing any of the
recommended remedies below other than remedies that require operation of the unit.
TROUBLE
Engine will not
start.
CAUSE
1. Engine flooded.
REMEDY
1. See “Starting a Flooded Engine”
in Operation section.
2. Fill tank with correct fuel mixture.
3. Install new spark plug.
2. Fuel tank empty.
3. Spark plug not firing.
4. Fuel not reaching
carburetor.
4. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
5. Contact an authorized service dealer.
5. Compression low.
1. Fuel not reaching
1. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
Engine will not
idle properly.
carburetor.
2. Carburetor requires
adjustment.
3. Crankshaft seals worn.
4. Compression low.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer
4. Contact an authorized service dealer.
1. Clean or replace air filter.
2. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
1. Air filter dirty.
2. Fuel not reaching
carburetor.
Engine will not
accelerate,
lacks power, or
dies under a
load.
3. Clean or replace spark plug
and re-gap.
3. Spark plug fouled.
4. Contact an authorized service dealer.
4. Carburetor requires
adjustment.
5. Carbon build up.
6. Compression low.
5. Contact an authorized service dealer.
6. Contact an authorized service dealer.
1. Choke partially on.
1. Adjust choke.
Engine smokes
excessively.
2. Fuel mixture incorrect.
2. Empty fuel tank and refill with
correct fuel mixture.
3. Air filter dirty.
4. Carburetor requires
adjustment.
3. Clean or replace air filter.
4. Contact an authorized service dealer.
Engine runs hot.
1. See “Fueling Engine” in Operation
section.
1. Fuel mixture incorrect.
2. Replace with correct spark plug.
3. Contact an authorized service dealer.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Contact an authorized service dealer.
4. Carbon build up.
-- 8 --
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS, INC.,
cover predelivery setup or normal adjustments
warrants to the original purchaser that each
new Weed Eaterr brand gasoline tool or at-
tachment is free from defects in material and
workmanship and agrees to repair or replace
under this warranty any defective gasoline
product or attachment as follows from the
original date of purchase:
explained in the instruction manual.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
The policy of ELECTROLUX HOME PROD-
UCTS, INC., is to continuously improve its prod-
ucts. Therefore, ELECTROLUX HOME
PRODUCTS, INC., reserves the right to
change, modify, or discontinue models, de-
signs, specifications, and accessories of all
products at any time without notice or obligation
to any purchaser.
2 YEARS - Parts and Labor, when used for
household purposes.
90 DAYS - Parts and Labor, when used for
commercial, professional, or income producing
purposes.
30 DAYS - Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance, or the use of
accessories and/or attachments not specifically
recommended by ELECTROLUX HOME
PRODUCTS, INC., for this tool. Additionally,
this warranty does not cover tune-ups, spark
plugs, filters, starter ropes, starter springs, cut-
ting line, or rotating head parts that will wear and
require replacement with reasonable use during
the warranty period. This warranty does not
U.S. EPA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGA-
TIONS: The U. S. Environmental Protection
Agency and ELECTROLUX HOME PROD-
UCTS, INC., are pleased to explain the emis-
sions control system warranty on your year
2002--2004 small off--road engine. ELECTRO-
LUX HOME PRODUCTS, INC., must warrant
the emission control system on your small off--
road engine for the periods of time listed below
provided there has been no abuse, neglect, or
improper maintenance of your small off--road
engine. Your emission control system includes
parts such as the carburetor and the ignition
system. Where a warrantable condition exists,
ELECTROLUX HOME PRODUCTS, INC., will
repair your small off--road engine at no cost to
you. Expenses covered under warranty include
diagnosis, parts and labor. MANUFACTUR-
ER’S WARRANTY COVERAGE: If any emis-
sions related part on your engine (as listed un-
der Emissions Control Warranty Parts List) is
defective or a defect in the materials or work-
manship of the engine causes the failure of such
an emission related part, the part will be repaired
or replaced by ELECTROLUX HOME PROD-
UCTS, INC. OWNER’S WARRANTY RE-
SPONSIBILITIES: As the small off--road en-
gine owner, you are responsible for the perfor-
mance of the required maintenance listed in
your instruction manual. ELECTROLUX HOME
PRODUCTS, INC., recommends that you re-
tain all receipts covering maintenance on your
small off--road engine, but ELECTROLUX
HOME PRODUCTS, INC., cannot deny war-
ranty solely for the lack of receipts or for your
failure to ensure the performance of all sched-
uled maintenance. As the small off--road en-
gine owner, you should be aware that ELEC-
TROLUX HOME PRODUCTS, INC., may deny
you warranty coverage if your small off--road
engine or a part of it has failed due to abuse, ne-
glect, improper maintenance, unapproved mod-
ifications, or the use of parts not made or ap-
proved by the original equipment manufacturer.
You are responsible for presenting your small
off--road engine to an ELECTROLUX HOME
PRODUCTS, INC., authorized repair center as
soon as a problem exists. Warranty repairs
should be completed in a reasonable amount of
time, not to exceed 30 days. If you have any
questions regarding your warranty rights and re-
sponsibilities, you should contact your nearest
authorized service center or call ELECTRO-
LUX HOME PRODUCTS, INC., at
1--800--554--6723.
WARRANTY
COM-
MENCEMENT DATE: The warranty period be-
gins on the date the small off--road engine is
purchased. LENGTH OF COVERAGE: This
warranty shall be for a period of two years from
the initial date of purchase. WHAT IS COV-
ERED: REPAIR OR REPLACEMENT OF
PARTS. Repair or replacement of any war-
ranted part will be performed at no charge to the
owner at an approved ELECTROLUX HOME
PRODUCTS, INC., servicing center. If you
have any questions regarding your warranty
rights and responsibilities, you should contact
your nearest authorized service center or call
ELECTROLUX HOME PRODUCTS, INC., at
1--800--554--6723.
WARRANTY PERIOD:
Any warranted part which is not scheduled for
replacement as required maintenance, or which
-- 9 --
is scheduled only for regular inspection to the ef-
fect of “repair or replace as necessary” shall be
warranted for 2 years. Any warranted part which
is scheduled for replacement as required main-
tenance shall be warranted for the period of time
up to the first scheduled replacement point for
that part. DIAGNOSIS: The owner shall not be
charged for diagnostic labor which leads to the
determination that a warranted part is defective
if the diagnostic work is performed at an ap-
proved ELECTROLUX HOME PRODUCTS,
INC., servicing center. CONSEQUENTIAL
DAMAGES: ELECTROLUX HOME PROD-
UCTS, INC., may be liable for damages to other
engine components caused by the failure of a
warranted part still under warranty. WHAT IS
NOT COVERED: All failures caused by abuse,
neglect, or improper maintenance are not cov-
ered. ADD-ON OR MODIFIED PARTS: The
use of add--on or modified parts can be grounds
for disallowing a warranty claim. ELECTRO-
LUX HOME PRODUCTS, INC., is not liable to
cover failures of warranted parts caused by the
use of add--on or modified parts. HOW TO FILE
A CLAIM: If you have any questions regarding
your warranty rights and responsibilities, you
should contact your nearest authorized service
center or call ELECTROLUX HOME PROD-
UCTS, INC., at 1--800--554--6723. WHERE TO
GET WARRANTY SERVICE: Warranty ser-
vices or repairs shall be provided at all ELEC-
TROLUX HOME PRODUCTS, INC., service
centers. Call 1--800--554--6723. MAINTE-
NANCE, REPLACEMENT AND REPAIR OF
EMISSION RELATED PARTS: Any ELEC-
TROLUX HOME PRODUCTS, INC., approved
replacement part used in the performance of
any warranty maintenance or repair on emis-
sion related parts will be provided without
charge to the owner if the part is under warranty.
EMISSION CONTROL WARRANTY PARTS
LIST: Carburetor, Ignition System: Spark Plug
(covered up to maintenance schedule), Ignition
Module. MAINTENANCE STATEMENT: The
owner is responsible for the performance of all
required maintenance as defined in the instruc-
tion manual.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
-- 1 0 --
|