2+1 SERIAL & PARALLEL PCI
HOST CARD
User Manual
Model: UGT-PC2S1P
All brand names and trademarks are properties of their respective owners.
w ww.vantecusa.com
Specifications
Model:
UGT-PC2S1P
Bus interface: PCI 32-bit
Ports:
2 x External Serial Port (DB9 Male)
1 x External Parallel Port (DB25 Female)
142 x 120 x 18mm
Dimension :
OS Support :
Windows® 2000, XP/2003/Vista/2008/7 (32/64 bit)
System Requirements
z
Windows® 2000, XP/2003/Vista/2008/7 (32/64 bit)
z
Computer with one available PCI slot
(CD-Rom Drive May Be Needed For Drivers)
Package Contents
z
z
z
z
1 x 2+1 SERIAL & PARALLEL PCI HOST CARD
1 x User’s Manual
1 x Driver CD
3 x Low Profile Bracket
UGT‐PC2S1P
Page 3
Layout
Before Installing the Vantec 2+1 SERIAL & PARALLEL PCI HOST
CARD, please see the photo below highlighting the available Parallel,
Serial ports of the card.
P1 & P2: Serial Ports
P3: Parallel Port
UGT‐PC2S1P
Page 4
Hardware Installation
1. Turn off the power to your computer.
2. Unplug the power cord and remove your computer’s cover.
3. Remove the slot bracket from an available PCI slot.
4. To install the 2+1 SERIAL & PARALLEL PCI HOST CARD,
carefully align the card’s bus connector with the selected PCI slot
on the motherboard. Push the board down firmly.
5. Replace the slot bracket’s holding screw to secure the card.
6. Replace the computer cover and reconnect the power cord.
Driver Installation
Note: Driver can also be found and downloaded from our website at
For Windows® 2000
1. At the Windows desktop click Start, then Run.
2. Type D:\UGT-PC2S1P \2000\PciSetup.exe, then click OK.
3. Press “Install” button to install the drivers.
4. Click “Exit” button.
5. Restart Windows to complete the installation.
UGT‐PC2S1P
Page 5
For Windows® XP/2003/Vista/2008/7 32bit
1. At the Windows desktop click Start, then Run.
2. Type
D:\UGT-PC2S1P\XP_2003_2008_Vista_7\32bit\PciSetup.exe,
then click OK.
3. Press “Install” button to install the drivers.
4. Click “Exit” button.
5. Restart Windows to complete the installation.
For Windows® XP/2003/Vista/2008/7 64bit
1. At the Windows desktop click Start, then Run.
2. Type
D:\UGT-PC2S1P\XP_2003_2008_Vista_7\64bit\PciSetup.exe,
then click OK.
3. Press “Install” button to install the drivers.
4. Click “Exit” button.
5. Restart Windows to complete the installation.
UGT‐PC2S1P
Page 6
To Verify Windows® Driver Installation
Click on the Device Manager tab in System Properties, which you
access from the Windows Control Panel. You should see two
High-Speed PCI Serial Port … and one PCI ECP Parallel Port …
installed under Ports (COM & LPT) item.
UGT‐PC2S1P
Page 7
Warranty
The 2+1 SERIAL & PARALLEL PCI HOST CARD comes with a 1
year limited warranty (90 day parts). If your unit becomes defective
information on how to receive warranty exchange or repair. Cosmetic
defects and missing parts are not covered under this warranty. Please
check the contents of the unit to make sure you received all parts. Also,
check for any cosmetic flaws. If any parts are missing or if there are
cosmetic defects, please contact the retailer from which you purchased
the unit immediately and ask for a replacement.
Vantec Thermal Technologies
43951 Boscell Rd. Fremont, CA 94538
Tel: 510-668-0368 fax: 510-668-0367
UGT‐PC2S1P
Page 8
|